The impact of carbon coating on the synthesis and properties of α''-Fe16N2 powders.

This paper presents the preparation of carbon composite Fe16N2 powders, and the influence of a protective carbon coating on the yield and magnetic properties of Fe16N2. Nanoparticle precursors with and without carbon were reacted under ammonia gas flow to produce Fe16N2. Neutron and X-ray powder diffraction indicate that the powders contain typically 40-60% Fe16N2, with the remaining phases being unreacted iron, Fe4N or Fe3N. Transmission electron microscopy demonstrates that the carbon coating is effective at reducing the level of sintering of Fe nanoparticles during the reduction stage prior to ammonolysis. XPS results support the retention of a carbon coating on the surface after ammonolysis, and that there is Fe-C bonding present at the particle surface. In situ TEM was used to observe loss of ordering in the nitrogen sublattice of carbon composite Fe16N2 powders in the range of 168 °C to 200 °C. Magnetic susceptibility measurements show maximum values for saturation magnetization in the range of 232 emu g(-1), and for coercivity near 930 Oe, for different samples measured up to 2 T applied field at 300 K.

Coalescence and sintering of Pt nanoparticles: in situ observation by aberration-corrected HAADF STEM.

An aberration-corrected JEOL 2200FS scanning-transmission electron microscope (STEM), equipped with a high-angle annular dark-field detector (HAADF), is used to monitor the coalescence and sintering of Pt nanoparticles with an average diameter of 2.8 nm. This in situ STEM capability is combined with an analysis methodology that together allows direct measurements of mass transport phenomena that are important in understanding how particle size influences coalescence and sintering at the nanoscale. To demonstrate the feasibility of this methodology, the surface diffusivity is determined from measurements obtained from STEM images acquired during the initial stages of sintering. The measured surface diffusivities are in reasonable agreement with measurements made on the surface of nanoparticles, using other techniques. In addition, the grain boundary mobility is determined from measurements made during the latter stages of sintering.

Suppression of proximity effect and the enhancement of p-wave superconductivity in the Sr2RuO4-Ru system.

We report unexpected phenomena observed on the Sr2RuO4-Ru eutectic phase featuring Ru islands embedded in a bulk crystal of the chiral p-wave superconductor Sr2RuO4. It was found that the Sr2RuO4/Ru interface is atomically sharp, terminated uniformly by a Sr/O layer. Surprisingly, the proximity-induced p-wave superconducting energy gap predicted by theory was not detected inside Ru islands. Our results suggest that the previously observed enhancement of superconductivity in this eutectic phase occurs away from rather than near the Sr2RuO4/Ru interface, where dislocations and phonon hardening were found.

Formation of ultrasharp vertically aligned Cu-Si nanocones by a DC plasma process.

We report an effective method for the production of ultrasharp vertically oriented silicon nanocones with tip radii as small as 5 nm. These silicon nanostructures were shaped by a high-temperature acetylene and ammonia dc plasma reactive ion etch (RIE) process. Thin-film copper deposited onto Si substrates forms a copper silicide (Cu3Si) during plasma processing, which subsequently acts as a seed material masking the single-crystal cones while the exposed silicon areas are reactive ion etched. In this process, the cone angle is sharpened continually as the structure becomes taller. Furthermore, by lithographically defining the seed material as well as employing an etch barrier material such as titanium, the cone location and substrate topography can be controlled effectively.

Biological strandard for electron microprobe analysis of intracellular sodium concentration.

A method is described for the determination of the intracellular concentration of sodium in individual cells using the electron microprobe analyzer. This method gives an accuracy equal to that obtained by using flame photometry on tissues with large cell populations. Intracellular sodium was precipitated in the cell by a fixative containing pyroantimonate. Cartilaginous needles from shark fins which were equilibrated in saline solutions of differing concentrations were used as biological standards.

Observations on normal and degenerating human otoconia.

Specimens of human otoconia obtained from autopsy material and representing various stages from fetal to advanced old age, were studied by microdissection, scanning electron microscopy, electron microprobe analysis, and x-ray powder diffraction. The typical adult otoconial configuration is a cylindrical, finely serrated body with pointed ends; crystallographically, it corresponds to a single crystal of calcite. Other, less numerous typed include jointed otoconia, pure rhombohedrons and multifaceted, presumably immature forms. Many otoconia achieve the adult configuration during fetal development. The multifaceted otoconia are most numerous, and the rhombohedrons proliferate, during childhon in the young adult, but saccular otoconia are the larger. In middle and advanced age the otoconia decrease in number, especially in the saccule. Saccular otoconia degenerate progressively in a posteroanterior direction across the macula; they assume a specific, fibours, hollowed-out appearance, which is not duplicated by either chemical etching or autolysis. Neogenesis and growth of otoconia appear to occur postnatally, with different characteristic growth potentials for those of the saccule and the utricle. Age-related saccular otoconial degeneration appears to involve the organic material, which disappears either before or simultaneously with the mineral substance.